Techniques

DIY Fabric-Covered Furniture: Simple No-Sew Makeovers

DIY fabric-covered furniture without sewing: pick sturdy fabric, staple the centres first, allow 3 to 4 inches to wrap, and cover seats and footstools.

On this page
  1. Which pieces suit a no-sew cover
  2. Tools you need
  3. Choose beginner-friendly fabric
  4. Measure and allow fabric
  5. Build the layers
  6. Cover a drop-in seat or footstool
  7. Cover a headboard
  8. Fusible web and adhesive options
  9. Finish the underside and edges
  10. Alternatives to a couch cover
  11. Fix the frame first
  12. Common mistakes
  13. Safety
  14. Next steps

You can cover a drop-in dining seat, a footstool, a headboard or an ottoman without sewing. The work is mainly stapling and gluing, so the results depend on sound fabric, good measurements and a sturdy base. Start with a simple piece, use a fabric that is hard-wearing enough for the job, and fix any wobbly frame before you cover it.

Which pieces suit a no-sew cover

Project Why it suits no-sew work Notes
Drop-in dining seat Flat, small and easy to remove Good first project. Staple to the underside.
Footstool or ottoman Simple shape with few corners Use a crate or table base if you like.
Padded headboard Flat face, fixed to the wall or frame Foam is usually 2 to 4 in. Fix it so it cannot tip.
Drawer front or panel Flat surface Glue the fabric in place with a flat-surface adhesive.

Pieces with curved or heavily shaped frames are harder without sewing. Save them for a later project.

Tools you need

No-sew does not mean no tools. You need:

  • A staple gun. Manual guns commonly take T50-type staples, and 1/4 to 3/8 in legs suit most fabric work.
  • Scissors, a tape measure and a flat screwdriver or staple remover.
  • Spray adhesive, if you are gluing any layers. Use it with ventilation.
  • Optionally, a fusible web and an iron (see below).

Choose beginner-friendly fabric

Medium-weight cotton duck, canvas, twill and plain-weave home decor fabrics are good choices. They hold their shape and staple cleanly.

Avoid stretch knits and slippery satins. They do not hold a staple well and pull out of shape. Quilting cotton works for panels and wall hangings, but it wears through quickly on a seat, so do not use it for seats.

Most upholstery and home decor fabric is 54 in (137 cm) wide. Most should not be washed before use, so check the care label first.

Measure and allow fabric

Allow about 3 to 4 in (8 to 10 cm) of extra fabric on each side so you can wrap the edges and staple them on the underside. Measure the finished size of the piece, add the wrap allowance (see how to calculate how much fabric you need), and then add extra for any pattern repeat.

Build the layers

Most no-sew covers use the same layers, from the base up:

  1. Base: plywood or MDF, checked for cracks and fixed firmly to the frame.
  2. Foam: high-density foam, cut to shape.
  3. Batting: polyester batting over the foam, so the surface feels soft.
  4. Fabric: the top layer, stapled on the underside.

Add a dust cover or felt on the underside, and cover the staple lines on visible edges with gimp or trim.

Cover a drop-in seat or footstool

  1. Remove the seat from the frame. Often a few screws from underneath hold it in place.
  2. Strip the old fabric and padding. Check the base for cracks.
  3. Fix the foam to the base with spray adhesive, then wrap it in batting.
  4. Lay the fabric face down and place the seat on top, with the centre of the front and back marked.
  5. Staple the centres first. Staple the centre of the front, then the back, then the sides. Pull with even tension.
  6. Work toward the corners. Staple out from the centres, stopping short of each corner. Then fold each corner neatly, as set out in how to fold a corner when upholstering.
  7. Fit a dust cover to the underside and check that the seat still fits the frame. Thick fabric can stop the seat from seating properly, so allow for it.

Cover a headboard

Headboard foam is usually 2 to 4 in (5 to 10 cm) thick. Measure the mattress width first, because headboards are usually sized to match:

  • Twin: 39 in
  • Full: 54 in
  • Queen: 60 in
  • King: 76 in

Fix the finished headboard to the wall or the bed frame so it cannot tip.

Fusible web and adhesive options

Fusible web (for example HeatnBond) bonds fabric hems with an iron, so you can finish raw edges without sewing. It is useful for the hem of a throw or a panel.

Mod Podge or diluted PVA can laminate thin fabric to a flat surface such as a drawer front. Brush a thin coat, smooth the fabric, and let it dry. For full details on gluing wood, see gluing upholstery fabric to wood.

Finish the underside and edges

Finish the underside of every piece with a dust cover or a layer of felt. This hides the staples, keeps dust out and makes the piece look finished from below.

On visible edges, cover the staples with gimp or a trim. Glue the trim in place, or tack it on, depending on the surface.

Alternatives to a couch cover

If you need a quick cover for a sofa or armchair, you have several options:

  • Throws and blankets draped over the back and arms work for a casual look, as long as the fabric is large enough to drape well.
  • Loose covers are slipped on rather than stitched in place. They suit a sofa or armchair that you want to change or clean.
  • No-sew covers fixed with staples or adhesive suit smaller pieces, such as footstools.

A custom cover is made to measure by a sewing professional or an upholsterer. Ask for a quote and a sample before you commit.

Fix the frame first

A wobbly frame will not hold new fabric well. Repair loose joints before you cover the piece, using glue or a suitable repair method. A weak frame wastes the materials you put into the new cover.

Common mistakes

  • Using quilting cotton on a seat. It wears through quickly.
  • Washing upholstery fabric before use. Most should not be washed.
  • Assuming no-sew means no tools. A staple gun is essential.
  • Covering a wobbly frame. Fix the joints first.
  • Stapling corners before the sides. Staple the centres first, then work out.

Safety

Use spray adhesive with ventilation. Fix headboards to the wall or the bed frame so they cannot tip. When you use a staple gun, keep your fingers clear of the nose.

Next steps

For a fabric-on-wood finish that is not a full upholstery job, see how to decoupage with fabric on furniture. For a first full project, see can you teach yourself upholstery.

The complete guide to techniques

Types of Upholstery Techniques Explained
Read the guide

Keep exploring

Guides from other topics

All topics →