Techniques

How to Make and Attach Piping for Upholstery

How to make and attach piping for upholstery: cut bias strips about 1.5 inches wide, join them, sew around the cord, then stitch it into the seam.

On this page
  1. Choose the cord
  2. Cut the strips
  3. Join the strips
  4. Sew around the cord
  5. Attach the piping to the seam
  6. Join the ends
  7. Double welt over show wood
  8. How much strip you need
  9. Common mistakes
  10. Safety
  11. Related steps

To make and attach piping for upholstery, cut fabric strips on the bias, join them into one long strip, wrap the strip around the cord and sew close to it with a zipper or piping foot. Then sandwich the finished piping into the seam, with the raw edges aligned, and stitch it in place.

Choose the cord

Standard upholstery welt cord is 5/32 in (about 4 mm) across. Larger cords, 1/4 in and up, are used for jumbo welt. Cord comes in cotton, polyester fibre or foam. If the covers will be washed, prewash cotton cord first, so it does not shrink after the piping is sewn.

Cut the strips

The strip width is the circumference of the cord plus two seam allowances. For 5/32 in cord with 1/2 in seam allowances, that works out to about 1.5 to 1.75 in (38 to 44 mm).

Cut the strips on the bias, at 45 degrees to the grain. Bias strips bend around curves and corners without puckering. On straight runs, straight-grain strips work well and use less fabric. Mark one end of each strip if the fabric has a nap, pile or directional pattern, so the direction stays consistent.

As a rough guide, one yard of 54 in fabric yields about 30 yards of 1.5 in strip. Waste varies with how you cut, so allow a margin.

Join the strips

Join the strips into one continuous length with diagonal (45-degree) seams, which spread the bulk. Place two strips right sides together, at a right angle or along a marked 45-degree line. Stitch across the join, trim the excess and press the seam open or flat. Repeat until you have the full length.

Sew around the cord

  1. Attach a zipper foot or a cording (piping) foot to the machine.
  2. Centre the cord on the wrong side of the strip, then fold the fabric over it so the raw edges meet.
  3. Sew as close to the cord as the foot allows, without stitching into the cord itself.
  4. Flatten the seam as you pass over each join.

A dedicated welt or cording foot gives tighter piping than a general zipper foot, so use one if you can.

Attach the piping to the seam

Sandwich the piping between the two layers of fabric, with the raw edges aligned. Stitch just inside the first line of stitching, so the seam holds the cord firmly.

At each corner, clip the piping seam allowance two or three times, so the piping turns cleanly around the corner. A walking-foot machine feeds the thick layers evenly, which helps keep the seam straight.

Join the ends

Overlap the two ends by about 1 to 2 in (25 to 50 mm). Trim the cord so the ends butt together, then fold the outer fabric end over the other, so the join is hidden.

Start and finish each join at the back or the bottom of the piece, never at a front corner, where it shows.

Double welt over show wood

Double welt uses two cords side by side. Along show wood, the cords are hot-glued or stapled over the raw edges. High-temperature hot glue is the usual trade method here, but it can burn skin, so keep your fingers clear of the nozzle and the molten glue.

How much strip you need

Measure the length of every edge the piping will follow, add a margin at each end, and then add a margin for the joins. Piping is often cut from a single long strip, so measure the total length first, then cut.

Common mistakes

  • Assuming bias is always needed. Straight grain is fine on straight edges.
  • Stitching too far from the cord. Stitch as close to it as the foot allows.
  • Using a general zipper foot for tight piping. A welt foot gives a neater result.
  • Treating piping as decorative only. It also reinforces and defines a seam.
  • Starting a join at a front corner. The join shows. Start at the back or bottom.

Safety

Hot glue for double welt causes burns, so keep your fingers clear of the nozzle and the molten glue.

Piping is often used on a boxed cushion, where it finishes the seams. See how to make a boxed cushion cover for furniture. It also finishes the front edges of a wingback, see how to upholster a wingback chair. For sewing sharp corners, see how to make corners pointy when sewing.

The complete guide to techniques

Types of Upholstery Techniques Explained
Read the guide

Keep exploring

Guides from other topics

All topics →