Techniques

How to fold a corner when upholstering?

How to fold a corner when upholstering: staple the sides first, pull the tip over, trim the excess to about 1/2 inch, then tuck a single or double pleat.

On this page
  1. Before you fold: finish the straight sides
  2. Step-by-step fold
  3. Single or double pleat
  4. Mitre fold
  5. Rounded corners
  6. Pleat direction on seats
  7. Common mistakes
  8. Safety
  9. Related steps

To fold a corner when upholstering, finish the straight sides first, stopping about 2 in (5 cm) short of each corner. Pull the corner tip diagonally over the corner and staple it underneath. Trim the excess to about 1/2 in (13 mm), then fold a single or double pleat, tuck it into shape and staple it on the underside.

Before you fold: finish the straight sides

The corner is the last part of a panel to be finished, so the straight sides must be secure first. Staple the front and back centres, then the sides, and work outward from the centres. Stop about 2 in short of each corner. If the sides are loose, the corner will wrinkle no matter how you fold it.

Step-by-step fold

  1. Pull the corner tip diagonally over the corner, keeping the fabric taut.
  2. Staple the tip underneath so the corner is anchored. Keep the staples close together.
  3. Trim the excess triangle inside the fold, leaving about 1/2 in (13 mm). Trim before the final fold, so the pleat lies flat and does not bulk up.
  4. Form the pleat. Choose a single or double pleat, as described below, and fold the remaining fabric into it.
  5. Tuck and shape the fold with a regulator or a flat screwdriver. The fold line should sit exactly on the corner edge.
  6. Staple the pleat on the underside, with the staples close together.
  7. Mirror the other corner. Left and right corners should match.

Single or double pleat

Single pleat. Fold one side over the other, so the fold line runs straight down the corner edge. This suits thin padding, roughly under 2 in (5 cm).

Double pleat. Fold both sides in, so two folds meet at the corner and form an inverted V. This suits thicker padding, about 2 in and up, and square-edged pads.

Round or trim the padding corners before you fold, so the fabric has less bulk to fold.

Mitre fold

On flat panels and boards, the two edges can meet on a diagonal. This is a mitre fold. Use it when the corner is flat and you want a clean line, not a pleat.

Rounded corners

Rounded corners need smaller, controlled pleats rather than one large fold. A tiny double pleat or V-shaped pleat works well. Trim the bulk gradually, so the curve stays smooth without puckering. Corner pleats, such as a box pleat, a hospital corner or a double V pleat on curved edges, are a common choice because they keep the excess out of sight.

Pleat direction on seats

On seats, point the pleats toward the back or the sides, so they are less visible from the front. Work the back corners first, then the front. Keep the pleats matching from left to right and front to back.

Common mistakes

  • Folding first, then trimming. Trim the excess before the final fold.
  • Mismatched pleats. Pleats that point in different directions look untidy. Mirror them.
  • Expecting the fold to remove all wrinkles. The sides must be tight. A pleat only finishes a tight corner.
  • Using one pleat on thick padding. Thick pads need a double pleat or a sewn corner.
  • Pulling the corner harder. Re-pull and re-staple the side to remove wrinkles instead.

Safety

Keep your fingers clear of the staple gun when you hold the fold tight. Use a regulator or flat screwdriver to hold the fold where you can.

For the full corner method, including the order for the whole panel, see how to do upholstery corners. For rounded seat corners, see how to reupholster a chair seat with rounded corners. For leather, see leather upholstery corners.

The complete guide to techniques

Types of Upholstery Techniques Explained
Read the guide

Keep exploring

Guides from other topics

All topics →