For most flat wood panels, spray adhesive or contact cement gives the most reliable bond. 3M Super 77 suits light fabric, and 3M Foam & Fabric 74 suits foam and heavier fabric. Glue is not a replacement for staples, though. Seats and other stress points still need staples, and glue alone can lift at the edges.
Glue for panels, staples for structure
Use glue where the fabric lies flat against wood, such as a panel, a box lid, a headboard face or trim. Use staples where the fabric has to take load or wrap around a frame, such as a seat. A common approach is to glue the face and staple the edges on the back, so the fabric is held at the points that do the work.
Choose an adhesive
| Adhesive | Best for | Notes |
|---|---|---|
| Spray adhesive (3M Super 77; 3M Foam & Fabric 74) | Super 77 for light fabric; Foam & Fabric 74 for foam and heavier fabric | Spray from about 6 to 8 in (15 to 20 cm) away, following the can label. Most need a short tack time before the fabric goes down. |
| Contact cement | Flat panels where the fabric is bonded in one go | Coat both surfaces and wait until dry to the touch, roughly 15 to 30 min (check the label). The bond is instant and cannot be repositioned. |
| Diluted PVA (white glue) or Mod Podge | Thin fabric laminated flat to wood, such as a drawer front | Dilute for spreading. Undiluted white glue soaks through thin fabric and stains it. |
| Fabric glue (for example Beacon Fabri-Tac or Aleene’s) | Gimp, braid and edges | Use for trim rather than whole panels. |
| Hot glue | Trim and double welt over show wood (high-temperature); lighter jobs on fabric (low-temperature) | Hot glue sets too fast for full fabric panels and leaves ridges. High-temperature glue can burn fabric and skin. |
| Hide glue | Traditional work, and repairs where the bond may need undoing later | Reversible with heat and moisture. |
Standard wood glue is not made for fabric. If you use one, test it on a scrap first.
Is Gorilla Glue better than fabric glue?
No single adhesive is better for every job. Gorilla Glue is a strong all-purpose glue, but it is harder to spread neatly over a large panel. For fabric, choose a product labelled for fabric or one of the adhesives in the table above, and test on a scrap before you commit the piece.
Prepare the wood
Good prep matters more than the choice of glue.
- Remove wax and finish from the area you will glue.
- Sand the surface to about 120 to 180 grit so the glue has a key.
- Wipe off the dust. If you clean the wood with a damp cloth, let it dry fully before you glue.
Glue fabric to wood with spray adhesive or contact cement
- Pre-press the fabric to remove creases.
- Cut the fabric with extra allowance. Leave enough to wrap the edges over the back.
- Apply the adhesive. For spray, work from about 6 to 8 in away, following the label. For contact cement, coat both surfaces and wait until dry to the touch.
- Place the fabric and smooth it from the centre outward with a brayer or J-roller. Work out any air.
- Wrap the edges over the back of the panel and staple them where you can.
- Clamp or weight the panel until the glue sets. Full cure is typically around 24 hours, so check the label.
Test on a scrap first. Thin or light fabrics can show glue bleed-through or darkening, so test the same adhesive and fabric on a piece of waste before you commit.
Glue thin fabric flat with diluted PVA or Mod Podge
For a thin fabric laminated flat, such as a drawer front, dilute the PVA or Mod Podge so it spreads easily. Brush a thin, even coat onto the wood, lay the fabric, and smooth it from the centre outward. Let it dry, and check the edges. If an edge lifts, add a little more adhesive under it and weight it down until it sets.
Temporary attachment: hot glue, double-sided tape, Velcro
Sometimes the fabric needs to come off again. Three common options each have a drawback.
- Hot glue can be used for a short-term attachment. It holds less well on finished wood, which can make it easier to remove later. Rubbing alcohol can help loosen it.
- Double-sided tape can be pulled off, but the longer it stays on, the stronger the bond. It can leave residue behind, and on painted or treated wood it can lift the finish.
- Velcro works well for swapping fabrics. Put the hook side on the wood and the loop side on the fabric, so you only need a new loop piece for each new fabric. Velcro can also leave adhesive and pull the finish when removed.
How to apply fabric to furniture
Upholstered furniture normally uses staples to fix fabric to the frame, with glue used for panels, trim and small projects. For a panel or box, the spray or contact method above applies. For a seat, staple the fabric, following a method such as how to reupholster a chair seat with rounded corners. For a no-sew project that uses both glue and staples, see DIY fabric-covered furniture.
Common mistakes
- Using glue as the only fixing on a seat. Staples are needed on seats and stress points.
- Using hot glue on full fabric panels. It sets too fast and leaves ridges.
- Using undiluted white glue on thin fabric. It soaks through and stains.
- Placing fabric as soon as you spray. Most spray adhesives need a short tack time first.
- Skipping the scrap test. Staining and bleed-through show up only after the fabric is down.
Safety
Use solvent adhesives and sprays with good ventilation, and keep them away from flames. High-temperature hot glue can cause burns, so keep your skin clear of the nozzle and the molten glue.
Related steps
For the trim that hides glued edges, see how to make and attach piping for upholstery. For how the whole craft fits together, see types of upholstery techniques explained.