Techniques

Upholstery Inside Corners: Techniques for a Smooth Fit

Upholstery inside corners: make a small Y-cut, tuck the flaps around the post, allow stuff-in fabric and staple them down for a smooth fit with no bunching.

On this page
  1. What makes an inside corner tricky
  2. Make the Y-cut
  3. Allow enough stuff-in fabric
  4. Stapling the flaps
  5. Padding around posts
  6. Corners around foam
  7. Curves and notched seats
  8. Sewing inside corners on cushions
  9. Leather and vinyl
  10. How to fold upholstery corners around foam without bunching
  11. Common mistakes
  12. Safety
  13. Learning the craft

To upholster an inside corner, make a small relief cut so the fabric can pass around a post or into a junction, then tuck the flaps down and staple them. Cut in small steps, leave enough fabric to pull through, and tension both sides evenly so no wrinkles run out from the corner.

What makes an inside corner tricky

Inside corners are where fabric meets an obstacle. The usual places are back posts, arm posts, and the junctions where the seat meets the arm or the back. Fabric that is pulled straight across these points will bunch or stand off the frame. Relief cuts give the fabric somewhere to go.

Make the Y-cut

A Y-cut is one straight cut from the fabric edge toward the post, followed by two short diagonal cuts that fan out to the post’s corners.

  1. Mark the corner. Fold the fabric back on itself to find where the post meets it, and mark the point on the back of the fabric.
  2. Start small. Stop the cut about 1/2 to 1 in (13 to 25 mm) short of the post. Check the fit, then deepen the cut in small steps if the fabric still will not lie flat.
  3. Tuck the flaps. Fold the cut flaps down around the post.
  4. Pull the main fabric through to the rail, so it sits flat against the frame, then staple it.

Make the cut in steps. An overcut leaves a gap on the visible side that cannot be repaired. A cut that is too shallow usually causes the wrinkles, so deepen it a little at a time.

Allow enough stuff-in fabric

Stuff-in, or tuck-in, is the extra fabric pushed into the gap where the seat meets the back or the arm. Allow about 3 to 6 in (8 to 15 cm), depending on how deep the gap is. Too little, and the fabric pulls out the first time someone sits down.

Stapling the flaps

Once the flaps are tucked:

  • Tension the fabric on both sides of the cut, so wrinkles do not radiate from the corner.
  • Use a regulator to push the fabric down into tight gaps.
  • Trim the excess near the staples, leaving enough material to hold them. Cut away from your hand in tight spaces.
  • If the fabric is loosely woven, seal the cut edges with a seam sealant such as Fray Check, so they do not unravel.

Padding around posts

Pad any gap around a post with a little batting before you cover it. A hollow spot that shows around a post is usually a padding problem, not a fabric problem. Add batting so the outline of the post is soft.

Corners around foam

Corners on foam are easiest when the foam itself is trimmed. Round or trim the foam corners so the fabric has less bulk to fold. Then make the relief cut and tuck the flaps around the foam, just as you would around a post. Fabric folded around a sharp foam edge tends to bunch, so trimming the foam first makes a flatter result.

Curves and notched seats

Notched drop-in seats, with cut-outs for the back legs, use the same relief-cut method. Curves work in a similar way. Make small cuts so the fabric can ease around the curve, and avoid one long cut that opens the seam. For a seat that needs curved corners, see how to reupholster a chair seat with rounded corners.

Sewing inside corners on cushions

On cushions and covers, the same idea applies, but the fabric is sewn rather than stapled:

  1. Mark the seam allowances and extend the seam lines past the corner on both sides.
  2. Sew up to the corner point, then stop with the needle down and lift the presser foot.
  3. Clip straight into the corner, leaving about 1/8 in (3 mm) of fabric so the thread has enough to bite.
  4. Open the clip, line up the adjoining edge, fold the excess flat, and continue stitching.

For more on sharp points, see how to make corners pointy when sewing.

Leather and vinyl

Leather and thick vinyl are stiffer and can resist a tight curve. Warm the material slightly with a hair dryer on low, and test the heat on a hidden area first. Avoid wetting finished leather, because it can stain or spot. For more on leather, see leather upholstery corners.

How to fold upholstery corners around foam without bunching

If the fabric bunches around a foam corner, the two usual causes are too much fabric in the fold and a relief cut that is too shallow or too deep. Trim the foam, check the cut depth, and re-pull the fabric before stapling. Bunching is rarely fixed by pulling harder.

Common mistakes

  • Making the full cut in one go. An overcut leaves a visible gap that cannot be fixed.
  • Cutting straight to the post’s corner without the Y. The fabric puckers.
  • Skipping the stuff-in allowance. Too little fabric pulls out under load.
  • Pulling harder to remove wrinkles. Usually the relief cut is too shallow.

Safety

Use sharp shears or a blade that cuts away from your hand, especially in tight spaces. Keep your other hand clear of the cutting line.

Learning the craft

If you are still deciding whether to learn upholstery at home, can you teach yourself upholstery covers a sensible first project. For the wider picture, see types of upholstery techniques explained.

The complete guide to techniques

Types of Upholstery Techniques Explained
Read the guide

Keep exploring

Guides from other topics

All topics →