A neat upholstered corner is mostly a matter of order. Get the straight sides tight first, then deal with the corners last. The method below works for most seats and arms with a standard corner, and it can be adapted for thicker padding or rounded edges.
Before you start
Check the padding before you pull any fabric. Trim or round the corners of the foam and batting so the fabric does not have to stretch over a sharp edge. Less padding at the corner means less bulk in the fold.
Padding thickness decides the fold. A single pleat suits thin pads, roughly under 2 in (5 cm). A double pleat, where two folds meet at the corner, suits thicker pads or square edges. Thick or stiff fabric may not fold well, and in that case a sewn corner is the better choice.
Step-by-step: folding a corner
- Staple the centre of each side first. Start with the front and back, then the sides. Pull with even tension so the fabric lies flat.
- Work outward from the centres. Stop about 2 in (5 cm) short of each corner. Keep the staples close enough to hold the fabric tight.
- Pull the corner tip diagonally over the corner. Hold it there while you shape the fold.
- Shape the fold. Use a regulator or a flat screwdriver to tuck the fold so the crease sits exactly on the corner edge. A straight fold line gives a crisp corner.
- Trim the excess inside the pleat. Leave about 1/2 in (13 mm) of fabric. Trim before the final staple, so the pleat lies flat and does not bulk up.
- Staple the pleat on the underside. Place the staples close together, roughly 1/4 to 1/2 in (6 to 13 mm) apart.
- Match the other corners. Left and right corners should mirror each other. On seats, point the pleats toward the back or the sides, away from the front view.
If the fold is visible on a tall stuffover corner, close it with a slipstitch using a curved needle.
Single or double pleat: which to use
Use a single pleat when the padding is thin and the corner is not too square. Fold one side over the other so the fold line runs straight down the corner edge.
Use a double pleat when the padding is thicker, or when the corner is square-edged and the fabric needs more fullness to lie flat. Fold both sides in so the two folds meet at the corner, forming an inverted V.
Mitre fold for flat panels
On flat panels and boards, the two edges can meet on a diagonal. This is a mitre fold. Pull the fabric taut over the corner, fold the excess inward at 45 degrees, trim the bulk underneath, and staple the remaining edge down.
Rounded corners
Rounded corners need smaller, controlled pleats rather than one large fold. Work them gradually, trimming bulk as you go so the curve stays smooth without puckering. The rounded seat guide walks through this on a seat, and the inside corners guide covers the concave side of a curve.
Common reupholstering mistakes
- Stapling the corners first. Corners are always done last. If the sides are loose, the corner will wrinkle.
- Leaving all the excess in the fold. It creates lumps and will not lie flat. Trim it.
- Pulling the corner harder to remove wrinkles. This distorts the grain and pattern. Re-pull and re-staple the side instead.
- Using one technique for every corner. Pad thickness and fabric weight decide the method.
- Covering over the old fabric without checking the base. Look at the foam and springs first, because a new cover will hide any problems underneath.
Making square corners
A square corner is usually made with a single or double pleat, or a mitre fold, on a square-edged pad. The key is tension. Keep the fabric tight to the corner, and make sure the fold lies on the corner edge before you staple it. If the corner still wrinkles, the sides are probably not tight enough. Re-staple them rather than pulling harder.
For thick fabric or a very square corner, a sewn corner can be more reliable. The boxed cushion guide shows the sewing approach for loose cushions, and how to make corners pointy when sewing covers sharp points on seams.
Safety
Keep your fingers clear of the staple gun nose when you hold a fold tight. Where you can, hold the fold with a regulator or flat screwdriver instead of your fingers.
Related steps
For a fold-by-fold walkthrough of the single and double pleat, see how to fold a corner when upholstering. Leather needs a different approach because it does not fray and its staple holes are permanent, so read leather upholstery corners before you work on hide.