Techniques

How to Make a Boxed Cushion Cover for Furniture

How to make a boxed cushion cover for furniture: measure the foam, cut the boxing with 1/2 inch seams, set a back zipper, then slide in the foam.

On this page
  1. Measure the cushion
  2. Work out the pieces
  3. Choose the fabric
  4. Make the zipper panel
  5. Notch the pieces
  6. Sew the boxing and the zipper
  7. Join the bottom panel
  8. Insert the foam
  9. T-cushions
  10. Common mistakes
  11. Safety
  12. Related steps

To make a boxed cushion cover, measure the foam, cut the face panels and the boxing with 1/2 in (13 mm) seam allowances, set a zipper along the back and wrap it around the back corners, then slide the foam in. A boxed cover has three parts: the top and bottom panels, the boxing strip that forms the sides, and the zipper panel.

Measure the cushion

Measure the cushion’s width, depth and thickness. Use the old cover as a pattern if it still fits well. Measure the foam, not the old cover, if the old cover has stretched.

Cut the foam about 1/2 in (13 mm) larger than the finished cover, in width and depth, for a firm fill. A cover made to the exact foam size will look baggy once the foam is in, so the extra size keeps the cushion full.

If you want a spreadsheet to work out the piece sizes, search for a cushion-cover calculator. Check any figures you get against your own measurements.

Work out the pieces

  • Boxing strip width: the cushion thickness plus 1 in (25 mm), to allow two 1/2 in seam allowances.
  • Zipper boxing: two strips, each half the boxing width plus a seam allowance. The zipper runs along the back and wraps around each back corner, by about 3 to 6 in (8 to 15 cm) on each corner.
  • Cut diagram: lay out the pieces on the fabric before you cut, to get the most from the length and width.

For a snugger fit, many makers take about 1/2 in off the thickness measurement for the boxing strip. Test this on a scrap first, because a boxing strip that is too tight will make the foam hard to insert.

Choose the fabric

Choose a fabric that will hold up to use. Upholstery fabric is rated by rub count, meaning how many double rubs it takes to wear the surface. For heavy-duty residential use, 15,000 double rubs or more is a common guide. For commercial use, look for 30,000 or more.

Check the cleaning code on the fabric label before you buy. Pattern matching matters on a boxed cover, so mark the front and back of each piece, and match stripes across the boxing seams.

Make the zipper panel

Use a #5 nylon coil zipper, cut about 6 in longer than the panel. Sew the zipper between the two zipper strips, with the zipper foot, so the zipper lies flat and does not fold.

Sew a few stitches to start, then stitch to the end. Run the zipper up and down to check that you have not stitched over it. If you have, remove those stitches and sew the section again.

Place a small piece of scrap fabric over the ends of the zipper and stitch over it, so the slider cannot come off the end.

Notch the pieces

Fold each piece in half and notch the centre point on the face panels, the boxing and the zipper panel. The notches keep the pieces lined up as you sew.

Sew the boxing and the zipper

  1. Match the centre-front notch of the top face panel to the centre-front notch of the boxing, with right sides together.
  2. Sew with a 1/2 in seam from the centre notch to the first corner.
  3. At each corner, find the pivot point and clip the seam allowance to the stitching, without cutting too deep.
  4. Turn the fabric at the pivot point, restack the pieces and continue along the next side.
  5. Stop about a third of the way down the side, leaving a long tail. Go back to the centre notch and sew in the other direction.

Repeat the same steps to join the zipper panel to the top face panel, so the zipper sits on one side of the cushion.

Overlap the boxing ends by about 2 in (5 cm) at the zipper, which hides the slider. This creates a pocket that hides the zipper ends.

Join the bottom panel

Attach the bottom panel in the same way as the top, starting at the notches and working around the boxing. Check that the notches line up all the way round.

Insert the foam

Turn the cover right side out, then check the fit. To get the foam into a tight cover, slide the foam inside a thin plastic bag, which helps it slip into the cover. Once the foam is in position, pull the bag out. Adjust the foam in the cover, then close the zipper.

Wrap the foam in polyester batting first, if you want a fuller look. Use spray adhesive with ventilation to hold the batting in place.

T-cushions

A T-cushion follows the same method, with extra corners at the T. Measure each section separately, and cut the boxing to follow each corner.

Common mistakes

  • Cutting the cover bigger than the foam. It ends up baggy.
  • Running the zipper only along the back. It needs to wrap the corners.
  • Assuming the cover can be washed. Most upholstery fabric shrinks or fades, so check the label before you buy.
  • Skipping welt. Welt on both seams helps the seams hold their shape. It is optional, but it is worth adding.

Safety

Use spray adhesive with ventilation, and keep it away from flames.

For piping, which is often used as welt on a box cushion, see how to make and attach piping for upholstery. For sharp corners on a cushion, see how to make corners pointy when sewing. For a boxed seat on a chair, see how to upholster a wingback chair.

The complete guide to techniques

Types of Upholstery Techniques Explained
Read the guide

Keep exploring

Guides from other topics

All topics →