Techniques

How to Upholster a Tight Back on a Chair

How to upholster a tight back on a chair: choose the support, build the layers, set the grain, allow stuff-in and fit muslin before the top fabric.

On this page
  1. What a tight back is
  2. Choose the support
  3. Build the layers
  4. Foam for the back
  5. Set the grain and pattern
  6. Stuff-in and relief cuts
  7. Stapling order
  8. Muslin first
  9. The outside back
  10. Common mistakes
  11. Safety
  12. Related steps

A tight back is upholstered directly to the frame, with no loose back cushion. To upholster one, choose the support, build the layers in order, set the grain, allow stuff-in at the bottom and fit muslin before the top fabric. Keep the tension lighter than you would on a seat, because an over-tight back flattens the padding.

What a tight back is

On a tight back, the padding and fabric are fixed to the back frame, so the back has a fixed, structured look. A loose back cushion, by contrast, sits on top of the frame and can be removed. Tight backs are a common choice for dining chairs, armchairs and wingbacks.

Choose the support

The support is the layer the padding sits on. Options include:

  • Elastic (rubber) webbing, a common choice for modern backs. The stretch varies by product, so check the maker’s specifications.
  • Sinuous springs, which are zigzag springs.
  • Coil springs.
  • Jute webbing, used on traditional work.

Whichever you choose, the support should be fixed firmly to the frame before any padding goes on.

Build the layers

Build the back in this order, from the support upward:

  1. Support (webbing or springs)
  2. Burlap
  3. Foam or fibre stuffing
  4. Polyester batting
  5. Muslin (calico)
  6. Top fabric

Each layer has a job. The burlap protects the support and the stuffing. The batting softens the surface. The muslin sets the outline before the top fabric goes on.

Foam for the back

Back foam is softer than seat foam (see what foam density is best for sofa cushions). A typical range is an ILD of about 20 to 30 and a thickness of about 1.5 to 3 in (4 to 8 cm). Check the supplier’s figures, because ranges vary.

To crown the back, add a thin layer of foam or batting at the lumbar area or the top edge. This gives a rounded shape without adding bulk everywhere.

Set the grain and pattern

Run the fabric grain vertically, so the back looks straight from the front. Centre the pattern on the back before you staple. Mark the centre on both the fabric and the frame so the pattern lines up.

Stuff-in and relief cuts

Allow about 4 to 6 in (10 to 15 cm) of stuff-in at the bottom of the back. This extra fabric is pulled through to the back rail, so the cover does not pull out when someone leans back.

Make relief cuts around the back posts and at the arm junctions, so the fabric can pass around them without bunching. Make the cuts in small steps, as with any inside corner.

Stapling order

Staple the centres first, then work out to the sides. Alternate between opposite sides as you go, so the tension stays even. Do not staple the corners until the sides are secure.

Muslin first

Fit a piece of muslin over the back before you cover it with the top fabric. The muslin shows you the shape and smoothness of the back before the final fabric goes on. Adjust the padding or the stapling if the muslin shows a sag or a lump.

The outside back

The outside back is the panel that covers the rear of the chair back.

  • Back-tack the top edge with cardboard tack strip.
  • Close the sides with a ply-grip metal tack strip, or slipstitch them with a curved needle.
  • Put cardboard or batting behind the panel. This stops the padding from pushing through the fabric.

Common mistakes

  • Pulling the fabric too tight. Over-tension flattens the padding and shows sag lines.
  • Skipping the muslin. It makes the top cover much smoother.
  • Using seat foam on a back. It is too firm for a back.
  • Stapling the back before the seat and arms. The inside back usually follows them.

Safety

Wear gloves when you handle metal tack strip, because the teeth are sharp.

For the wider build order, including the seat and arms, see how to upholster a wingback chair. For a tufted back, see how to do button tufting on upholstered furniture. For the method behind the layers, see types of upholstery techniques explained.

The complete guide to techniques

Types of Upholstery Techniques Explained
Read the guide

Keep exploring

Guides from other topics

All topics →