To reupholster a chair seat with rounded corners, remove the seat, strip the old cover and rebuild the padding with foam and batting. Stretch the fabric from the centres of each side, staple it outward, and make small, even pleats at each curve. Keep every gather on the underside so none shows past the edge.
Remove the seat and strip the old cover
Many drop-in seats come out after a few screws from underneath the frame. Turn the chair over and check how the seat is fixed before you unscrew anything.
Pull out the old staples and fabric with a staple remover, a flat screwdriver or pliers. Wear eye protection while you do it. Check the base for cracks, because a base that is split or worn will not hold the new staples. The base is often 1/2 in (13 mm) plywood.
Rebuild the padding
Use high-density foam, about 1 to 2 in (25 to 50 mm) thick, for a drop-in seat. Bevel or round the outer edge of the foam so the seat has a softer crown and does not look boxy. Cut the foam slightly oversize, about 1/4 to 1/2 in (6 to 13 mm), or bevel the edges, depending on the look you want.
Bond the foam to the base with spray adhesive. Then lay polyester batting over the foam and trim it to the foam edge, or slightly smaller, so the corners do not get bulky.
Cut the fabric
Cut the fabric with about 3 to 4 in (8 to 10 cm) of extra margin all round, so you have enough to grip and pull. Mark the front and back centres on both the fabric and the seat base, so the pattern lines up.
Rounded corners are covered on the bias, which stretches and eases the fabric around the curve. If the fabric has a pattern, check that it runs straight across the front before you cut.
Anchor the centres
Place the fabric face down. Stack the batting, foam and seat base on top, with the marks lined up. Staple the centre of the front edge while you pull the fabric taut. Repeat at the back, then the left and right centres, and leave the corners unstapled for now.
Work toward the curves
Pull the fabric tightly over each rounded edge and add staples moving outward from each centre. Stop just before each curved corner. Space the staples close together on the curves, about 1/4 to 1/2 in (6 to 13 mm) apart.
Pull the fullness down evenly as you go. Pulling harder in one spot causes puckers, while spreading the fullness evenly keeps the top smooth.
Pleat the rounded corners
At each rounded corner, make small, even pleats, or a neat double pleat, rather than one large fold. A large single pleat on a round corner tends to leave a lump. Trim the excess fabric under the seat, without cutting through the layers you still need to staple.
Keep all the gathers on the underside, so none show past the edge of the seat.
An option for very thick padding. One DIY blogger, reupholstering dining chairs with very thick padding and rounded corners, used a single pleat at each corner. The staples were placed on a 45-degree line, sloping toward the corner, so each side had room to finish. Check the top carefully for wrinkles at the corner if you use this approach, because the final flap can pull across the corner and wrinkle.
Finish the underside and refit
Tap down any raised staple heads with a hammer. Attach a dust cover, cambric or black cloth, stapled underneath. Then screw the seat back onto the chair.
Allow for the added fabric thickness when you refit. Thick fabric can stop the seat from sitting properly on the frame. If the seat does not fit, the base edge may need to be shaved, but check the frame first, because the base may have been fitted tightly from the start.
Common mistakes
- Using one large pleat on a round corner. It leaves a lump. Use small, even pleats.
- Pulling harder to fix puckers. Spread the fullness evenly instead.
- Stapling corners before the centres. The centres anchor the fabric, so do them first.
- Forgetting the refit. Added fabric can stop the seat fitting the frame.
Safety
Wear eye protection when you remove old staples. Keep fingers clear of the staple gun nose when you hold a pleat tight.
Related steps
For the general corner method, see how to do upholstery corners. For the fold itself, see how to fold a corner when upholstering?. For a first project to build confidence, see can you teach yourself upholstery.