To remove staples from furniture without damaging the frame, use a proper staple lifter, pull in line with the staple legs, and protect the wood around each staple. A flat screwdriver is a last resort, because it slips more often and can dent the wood. Work slowly, and expect the job to take a while on a larger piece.
Use a proper staple lifter
A staple remover, or lifter, has a forked or flat blade that slides under the staple crown. Once the blade is under the crown, you lever it upward. Needle-nose pliers or end nippers then grab the staple once it is partly lifted.
A flat screwdriver can work in a pinch, but it slips more and leaves marks on the wood. The tools guide covers the other tools you may need.
Step-by-step removal
- Slide the tip under the crown. Push the lifter until the blade sits under the top of the staple.
- Lever it up gently. If the staple sits flush or deep in hardwood, tap the tool lightly with a hammer to get it started.
- Rock or twist it. Move the staple sideways to loosen the legs without snapping the metal.
- Pull it out. Grip the lifted staple with pliers and draw it out.
Pull in line with the staple legs. Pulling at an angle enlarges the hole and can tear the fabric or split the wood.
Protect the show wood
Where a staple sits near finished wood, slip a thin metal scraper or a piece of cardboard behind the lever. The protective layer spreads the force and keeps the finish from being dented. Prying directly against show wood with a screwdriver is a common cause of dents.
Remove the layers in order
Work from the outside in. Remove the dust cover and the outside back first. Cut away any loose fabric near the staple rows so you can see the staples clearly. Keep each piece, because you may use it as a pattern. The take-apart guide covers the full order.
Broken staple legs
Sometimes a staple breaks. If you can grip what is left, pull it out with pliers. If not, snip the remaining leg or tap it flush with a hammer. A leftover leg can block a new staple, so remove it when you can.
Tacks on older pieces
Older furniture, such as an antique couch, often uses tacks instead of staples. Use a tack lifter, or a ripping chisel and a mallet. Strike the chisel along the grain rather than across it, because working with the grain reduces splitting in the rails.
Repair holes in the rails
Rails with many old holes may not hold new staples well. You can repair them in one of two ways:
- Wood glue and a toothpick or sliver. Fill the hole with glue and a small piece of wood. Trim it flush once the glue sets.
- Wood filler. This fills larger holes, but it holds new staples less well than solid wood.
Let the repair cure fully before you staple into it.
Which staples can stay?
Flush, well-seated staples on hidden rails can sometimes be left in place. Whether to remove them is a judgment call. If a staple is loose, or if it sits where you need to put a new staple, remove it.
Time and staple count
Stripping an armchair can take roughly 2 to 5 hours. A sofa can hold thousands of staples, so plan for a long session.
Clean up
Collect the staples in a container as you work. When you finish, sweep the area with a magnet to pick up any that have dropped. Stray staples are easy to step on and hard to see.
Mistakes to avoid
- Yanking staples out with fabric still attached. This can split the rails.
- Prying against show wood. This dents the finish.
- Using a grinder to shave staple tops. Some online suggestions do this. It can gouge the wood underneath, so it is not recommended here.
Safety
Wear eye protection. Staples can fly when they release. Wear gloves, because staple legs and tack points are sharp.
Frequently asked questions
Do I have to remove every staple? Not always. Flush, well-seated staples on hidden rails can sometimes stay. The complete guide to reupholstering furniture explains the rest of the process, including when that is a reasonable choice.
What tool should I buy for staples? A forked or flat-tipped staple lifter is the usual choice. It slides under the crown more easily than a screwdriver. The tools guide explains which tools suit which jobs.