DIY Reupholstery

How to Reupholster a Recliner at Home

How to reupholster a recliner at home, from unplugging the power and removing the back to sewing panels, reattaching with hog rings and testing the recline.

On this page
  1. Is your recliner a good DIY project?
  2. Tools and materials
  3. Step 1: Unplug and disconnect the power
  4. Step 2: Remove the back
  5. Step 3: Remove the old cover
  6. Step 4: Repair the frame, springs and foam
  7. Step 5: Cut the new panels
  8. Step 6: Sew the panels and reattach the cover
  9. Step 7: Test the recline
  10. Safety
  11. Time and alternatives
  12. Frequently asked questions

You can reupholster a recliner at home, but it is one of the harder DIY jobs. Most recliner covers are sewn panels rather than simple stapled pieces, and the mechanism needs care. If this is your first upholstery project, a dining seat or footstool is a better place to start. The beginner projects guide lists those options.

Is your recliner a good DIY project?

Consider these questions:

  • Is it a power recliner? If so, the motor and switch must be disconnected before you start.
  • How is the cover built? Most recliner covers use sewn panels, sometimes with staples or hog rings.
  • Do you have a walking-foot sewing machine? Domestic machines can struggle with welt and heavy layers.
  • Are you comfortable working around the mechanism without taking it apart?

If the answer to most of these is no, consider replacement covers from the manufacturer or a fitted slipcover. Both options are covered below.

Tools and materials

  • A walking-foot sewing machine, or a machine that handles heavy layers
  • A seam ripper
  • Hog ring pliers and hog rings
  • A staple remover and a staple gun
  • A flat screwdriver, for the back brackets
  • Fabric: roughly 6 to 8 yards for a standard recliner, depending on the style and the pattern repeat

Choose durable fabric with a slight give, or upholstery vinyl or leather, because recliners flex constantly. Heavy-duty residential fabrics are commonly rated at 15,000 Wyzenbeek double rubs or more. Check the rating on the bolt before you buy.

Step 1: Unplug and disconnect the power

If the recliner is powered, unplug it before you do anything else. Then disconnect the motor and switch cables. Label each cable as you disconnect it, so you can reconnect them correctly.

Step 2: Remove the back

Most backs lift off. Release the locking tabs on the back brackets, often with a flat screwdriver, and lift the back straight up. Take photos before you start, so you know how the back goes back on.

Do not force the back. If it will not lift, look for a tab or screw you have missed.

Step 3: Remove the old cover

  • Lay the chair on its back or side to reach the underside staples.
  • Unpick sewn seams with a seam ripper, cutting carefully so you do not cut the panels.
  • Remove staples, hog rings, listing rods or J-strips, and any hook-and-loop tape.
  • Label each panel before you take it off, then trace it as a pattern.

Keep the panels whole. They are the patterns for the new cover.

Step 4: Repair the frame, springs and foam

Check the frame for loose brackets and sharp edges that could tear the new fabric. Tighten what is loose. Replace foam that is flattened or crumbling. Keep fabric and padding clear of the moving parts, and do not take the mechanism apart.

Step 5: Cut the new panels

Cut each panel from its old pattern, adding seam allowance that matches the original. A common seam allowance is about 1/2 inch.

Check the fabric direction and any nap before you cut. Mark the top and front of each panel so they go back in the right place.

Step 6: Sew the panels and reattach the cover

  • Sew the panels and piping together. A walking-foot machine helps with welt and thick layers.
  • Reattach the cover with hog rings where the original used them. Use hog ring pliers and new hog rings.
  • Staple or tack where the original used staples or tack strip.

Step 7: Test the recline

Reassemble the chair and recline it fully. Check that the fabric does not bind or catch in the mechanism or the footrest. Thick fabric can bind, so if it does, adjust the cover before you finish.

Safety

  • Unplug power recliners before you start.
  • Keep your hands clear of the scissor mechanism, which can snap closed.
  • Wear eye protection when you cut hog rings or pull staples.

Time and alternatives

A first recliner can take roughly 15 to 30 hours or more, depending on your skill and the style. If that is more than you want to take on, consider two alternatives:

  • Manufacturer replacement covers, which are made to fit the original shape.
  • Fitted slipcovers, which cover the chair without stapling or sewing.

For a broader view of costs and when a professional is worth it, see the cost guide.

Frequently asked questions

Can I use a regular sewing machine? You can try, but a walking-foot machine handles welt and heavy layers much better. A domestic machine may struggle with the thickness.

Why does thick fabric matter so much? Thick fabric adds bulk around the footrest and the mechanism. When the recliner moves, that bulk can bind. Test the recline before you finish the job.

What should I take apart first? Start with the back, then the cover. Do not take apart the mechanism. The take-apart guide explains how to record each step as you go.

The complete guide to diy reupholstery

How to Reupholster Furniture: A Complete DIY Guide
Read the guide

Keep exploring

Guides from other topics

All topics →