DIY Reupholstery

How to Reupholster an Ottoman: Step-by-Step DIY Guide

How to reupholster an ottoman step by step: remove the legs and old cover, replace the foam, staple the new fabric from the center and finish the corners.

On this page
  1. What you need
  2. Step 1: Turn it over and remove the legs
  3. Step 2: Remove the dust cover, staples and old fabric
  4. Storage ottomans
  5. Step 3: Replace the foam
  6. Step 4: Wrap the foam in batting
  7. Step 5: Cut the fabric
  8. Step 6: Center and staple
  9. Step 7: Finish the corners
  10. Step 8: Finish the underside and reattach the legs
  11. Optional: button tufting
  12. Common mistakes
  13. Safety
  14. Frequently asked questions

A simple ottoman is one of the more approachable upholstery projects. An untufted piece usually takes about 2 to 4 hours. The steps are: remove the legs and old cover, replace any worn foam, cut the fabric with extra margin, and staple from the center out. Then finish the corners and the underside, and reattach the legs.

What you need

  • Fabric: roughly 1 to 3 yards, depending on the size of the ottoman and any pattern repeat
  • High-density foam, usually 2 to 4 inches thick on top, if the old foam is worn
  • Polyester batting
  • Spray adhesive, used with good ventilation
  • A staple gun and staples
  • Cambric, for the dust cover
  • A screwdriver, pliers, scissors and a tape measure
  • An electric carving knife, for cutting foam

Step 1: Turn it over and remove the legs

Turn the ottoman upside down on a clean surface. Photograph the hardware and the fabric layers before you take anything apart. Unscrew the legs if they come off.

Step 2: Remove the dust cover, staples and old fabric

Remove the dust cover first, then the staples, then the old fabric. Pull staples with pliers or a staple lifter. Keep the intact pieces of the old fabric as your pattern. For a closer look at removing staples without damaging the frame, see the staple removal guide.

Storage ottomans

If the ottoman lifts open, remove the hinges first. Upholster the lid and the box as separate pieces. This makes each piece easier to handle and to fit.

Step 3: Replace the foam

If the foam is flat or crumbling, replace it with high-density foam, usually 2 to 4 inches thick on top. Cut the foam with an electric carving knife, which gives a cleaner edge than scissors. Bond it to the top with spray foam adhesive, and work in a ventilated space.

Step 4: Wrap the foam in batting

Cover the foam and the sides with a layer of polyester batting. This smooths the edges so they do not look hard and square.

Step 5: Cut the fabric

Cut the fabric with about 3 to 4 inches of extra beyond the bottom edge on all sides. Add extra for any piping or pattern repeat. The measuring guide explains how to allow for repeats and waste.

Step 6: Center and staple

  1. Center the fabric over the padded top.
  2. Staple once at the middle of each side, working opposite sides in turn.
  3. Work outward from the centers, stopping about 2 to 3 inches short of each corner.

Starting at the corners causes puckers. Always start from the centers.

Step 7: Finish the corners

Fold each corner into a neat fold or pleat, and trim the inner bulk. A boxed ottoman with sewn corners may need a sewn cover rather than stapling alone. The tips guide explains corner pleats in more detail.

Step 8: Finish the underside and reattach the legs

Staple new cambric to the bottom, with the edges folded under. To find the leg holes, feel for them through the cambric. Cut a small X at each hole rather than a large opening, then reinstall the legs.

Optional: button tufting

Button tufting multiplies the fabric and the time. If you want buttons:

  1. Mark a grid on the top.
  2. Drill holes through the base at each mark.
  3. Pull the buttons through with a long needle and twine.
  4. Staple the twine underneath.

Tufting is not a beginner add-on. Try an untufted ottoman first.

Common mistakes

  • Stapling corners first. This causes puckering. The centers come first.
  • Using thin craft foam. It will not hold up as a footrest or seat.
  • Skipping the batting. Without it, the foam edges look hard.

Safety

Wear eye protection when you remove and drive staples. Use spray adhesive with good ventilation.

Frequently asked questions

How much fabric do I need? Roughly 1 to 3 yards, depending on the ottoman’s size and any pattern repeat. Add the margins above, and check the figure against your own measurements.

Is an ottoman a good first project? A simple, untufted ottoman is a good second project, after a dining seat. The beginner projects guide lays out the order.

The complete guide to diy reupholstery

How to Reupholster Furniture: A Complete DIY Guide
Read the guide

Keep exploring

Guides from other topics

All topics →