Reupholstering furniture means taking a piece down to its frame where needed, replacing the padding and fabric, and putting a new cover on. It is a practical project for many chairs, footstools and benches. It is a bigger job for sofas and recliners. This guide walks through the whole sequence, from deciding whether a piece is worth the work to the final staple.
Is reupholstering the right call?
Before you buy fabric, check the piece. A solid wood frame with sound springs is a good candidate. A frame held together with staples or particleboard rarely justifies the labor. A piece with sentimental value or a good frame is more likely to pay off for the effort.
Compare the cost before you commit. Professional labor can be substantial, and a new piece may cost less than a professional job on a budget sofa. The cost guide gives rough ranges for labor and fabric.
Start with a simple first project
Dining chair seats (often called slip seats), footstools and benches are good first projects. They are small, they have straight edges, and mistakes cost less. A dining seat can take about an hour once you have done a few. A sofa is a poor first project, because its yardage, number of pieces and fabric waste make errors expensive. The beginner projects guide lays out a progression from seats to headboards.
Tools and materials
You will need a staple gun, a staple remover, needle-nose pliers, fabric shears, a measuring tape and chalk. For a sofa, a pneumatic staple gun is standard. Polyester batting, spray adhesive, a dust cover and upholstery-weight fabric complete the basic list. The tools guide explains what each tool does and which ones you can leave until later.
Step 1: Photograph and strip the piece
Photograph the piece from all sides before you start, and again at each stage. Note where the welt sits, where pleats fold, and where fabric pulls through to the underside. Then take the piece apart in the reverse of the order it was built.
In most pieces, the dust cover and outside back come off first, followed by the outside arms, arm fronts, inside back and inside arms. The seat or deck comes off last. Label each old fabric piece with its name and orientation, such as “top” or “front,” and keep it whole. Those pieces become your patterns.
Staples are the most tedious part. A proper staple lifter is safer than a screwdriver, and the staple removal guide explains how to avoid splitting the rails. For more detail on taking a chair apart, see the take-apart guide.
Step 2: Inspect and repair the frame, springs and webbing
With the old fabric off, check the frame. Tighten or re-glue loose joints and clamp them while the glue sets. Look for cracked corner blocks and split rails. Check the springs and webbing for broken spring clips, snapped twine ties, and slack or torn webbing.
Fixing these problems now is much easier than re-covering a piece that sags a year later. A new cover over a weak frame hides the problem but does not solve it.
Step 3: Replace the padding
Replace foam that is flattened, crumbling or yellowed. For seats, high-density polyurethane foam is common, roughly 1.8 pounds per cubic foot or more. Backs are often softer. Cut the foam about half an inch larger than the finished cover, then wrap it in polyester batting so the edges look smooth.
Good cotton or horsehair padding can sometimes be reused. Do not keep old padding by default, though. Check its condition first, because worn padding often leaves lumps under a new cover.
Step 4: Measure, pattern and cut the new fabric
Lay the old pieces on the new fabric and trace them, allowing extra for pulling and stapling. A common starting point is about 2 to 4 inches of extra fabric per stapled edge, with more where the fabric tucks into the frame. Standard upholstery fabric is usually 54 inches wide.
If the fabric has a large pattern repeat, add roughly 10 to 25 percent to the yardage. The measuring guide has a full list of allowances and rough yardage by piece.
Check the fabric direction before you cut. Fabric with a nap, such as velvet, or a one-way print needs every piece cut in the same direction.
Step 5: Stretch and staple from the center out
This is where a piece starts to look finished. Mark the center of each side. Place a staple in the middle of one side, pull the fabric taut from the opposite side, and place a staple there. Repeat for the other two sides.
Then work outward toward the corners, alternating sides so the tension stays even. Staple close to, but not on, the edge of the rail, and stagger the rows so the wood does not split.
Pull firmly but do not over-stretch. Fabric pulled too tight distorts the weave and pulls the pattern off line. More staples will not fix poor tension.
Step 6: Corners and finishing
Corners are where most of the bulk builds up. Fold the excess into one or two neat pleats, trim the inner bulk before stapling, and staple the corners flat. On a straight outside back, a cardboard tack strip gives a crisp top edge. Metal ply-grip or curve-ease strips close the side edges neatly.
Finish the underside with a dust cover, which is a black cambric fabric stapled on with its edges folded under. Reattach the legs and any hardware. Then check how the piece feels to sit in.
Common reupholstering mistakes
- Stapling over the old cover. This hides faults in the frame and springs, and the result is often bulky. It is covering over, not full reupholstering. See can you reupholster over existing fabric.
- Using quilting or apparel cotton. It is not upholstery fabric and wears through quickly.
- Pulling the fabric too tight. This distorts the weave and the pattern.
- Using low-density foam. It flattens quickly, no matter how thick it is.
- Using a light-duty staple gun on hardwood. It may not drive staples fully.
- Skipping batting. Batting protects the fabric from the foam and smooths the edges.
Is it cheaper to reupholster or buy new?
It depends on the piece and the fabric. For a budget sofa, a new piece can cost less than a professional reupholstering job. For a well-built frame, reupholstering is often the better value. DIY saves labor, but you still pay for fabric and foam, and a first attempt may waste some fabric.
Safety
Wear eye protection when pulling and driving staples, because they can fly when they release. Wear a dust mask when stripping old padding, which can hold dust, mold and older flame-retardant treatments. Wear gloves when handling old springs and tack-filled rails. If you use an air-powered staple gun, disconnect the air hose before clearing a jam.
Frequently asked questions
What is the easiest way to reupholster a chair? Start with a dining seat that unscrews from the frame. Strip the old cover, replace the foam if it is worn, and staple the new fabric from the center out. The beginner projects guide lists the steps.
How much does it cost to reupholster a chair? Costs vary widely. As rough US ranges, professional labor for a dining seat is about $25 to $75, and labor for an armchair is about $300 to $900, before fabric. Prices vary by region and by shop.
Can you reupholster over existing fabric? Sometimes, for simple pieces with clean, sound old fabric. The over-existing-fabric guide has a checklist for deciding.