DIY Reupholstery

Essential Upholstery Tools for Reupholstering a Sofa or Chair

Essential upholstery tools for reupholstering a sofa or chair, from staple removers and guns to shears and needles, plus what beginners can skip.

On this page
  1. Tools for removing old fabric
  2. Staple guns and fasteners
  3. Hammers, stretchers and shaping tools
  4. Cutting and sewing tools
  5. Consumables
  6. What to buy first
  7. What you can leave for later
  8. Safety
  9. Common tool mistakes

Reupholstering a sofa or chair takes a small set of tools, and a few of them matter most. This guide covers what each one does, what to buy first, and what you can leave until later. For the bigger picture, see the complete guide to reupholstering furniture.

Tools for removing old fabric

A staple remover, or staple lifter, has a forked or flat blade that slides under the staple crown and levers it up. A flat screwdriver can do the job in a pinch, but it slips more often and marks the wood. A tack lifter, or a ripping chisel and mallet, handles the tacks found on older pieces.

End nippers or needle-nose pliers grip a staple that is already partly lifted. Nippers can also snip a broken leg flush. For a full method, see the staple removal guide.

Staple guns and fasteners

The pneumatic staple gun is the standard tool for sofas and chairs. A common setup uses 20- to 22-gauge staples with a 3/8-inch crown and 1/4- to 1/2-inch legs. Pneumatic guns usually run at about 60 to 90 PSI, though you should check the rating on your own tool. A pneumatic gun needs a compressor.

Electric staple guns suit lighter jobs such as slip seats. Manual staple guns, especially small T50-type models, can struggle to drive staples into hardwood. Staples must match the gun’s staple series, so check the manual before you buy a box.

Hammers, stretchers and shaping tools

A magnetic upholstery hammer has one magnetic face that holds tacks and decorative nails in place while you strike them. A webbing stretcher tensions jute or elastic webbing before you fasten it. A regulator is a long, pointed tool that shifts stuffing and helps neaten pleats.

Cutting and sewing tools

Fabric shears of about 10 to 12 inches should be used on fabric only. Household scissors dull quickly and can fray upholstery fabric. For foam, an electric carving knife or a foam saw gives a cleaner cut than scissors.

For hand stitching, curved needles (about 3 to 6 inches) handle most closing work. Long double-pointed straight needles (about 10 to 12 inches) help with buttons. A walking-foot sewing machine handles welt and thick layers well, while a domestic machine works for lighter fabric. Hog ring pliers and hog rings attach covers to wires on recliners and car seats.

Consumables

Keep spray foam adhesive, upholstery thread, button twine, welt cord, tack strip, chalk and T-pins on hand. These get used up quickly, so buy them with your first project in mind.

What to buy first

For a first project such as a dining seat, the core list is:

  • A staple gun (electric or manual is enough for a slip seat)
  • Staples that match the gun
  • A staple remover and needle-nose pliers
  • Fabric shears and a tape measure
  • Chalk and spray adhesive

A slip seat does not need industrial tools. Sofas are different. For a sofa, a pneumatic or strong electric gun is the practical choice. Start with the beginner projects guide if you are not sure what to practice on.

What you can leave for later

Hog ring pliers, a walking-foot machine and a webbing stretcher are useful, but most first projects do not need them. Webbing matters once you replace or re-tension it, and hog rings matter mainly for recliners and some car seats.

Safety

Wear eye protection when you pull or drive staples. Disconnect the air hose from a pneumatic gun before you clear a jam.

Common tool mistakes

  • Using a screwdriver to lift staples. It marks the wood more than a proper lifter does.
  • Using household scissors on upholstery fabric. They dull quickly and fray the weave.
  • Buying staples that do not match the gun. The gun may jam or not drive them at all.
  • Assuming a sofa can be done with a light manual gun. Hardwood frames often need more driving force.

The complete guide to diy reupholstery

How to Reupholster Furniture: A Complete DIY Guide
Read the guide

Keep exploring

Guides from other topics

All topics →