Techniques

How to Do Button Tufting on Upholstered Furniture

How to do button tufting on upholstered furniture: plan the grid, cut holes in the foam, allow extra fabric for depth, then set each button with twine.

On this page
  1. What button tufting is
  2. Plan the button grid
  3. Cut holes in the foam
  4. Allow extra fabric for depth
  5. Choose and cover the buttons
  6. Set the buttons
  7. Set the pleats
  8. Fabric choice
  9. Common mistakes
  10. Safety
  11. Related steps

To do button tufting on upholstered furniture, plan a button grid on the backing, cut holes in the foam at each button point, and allow extra fabric for depth. Then pull each button through the foam and fabric with twine, and set the pleats between the buttons. Buttons pressed into solid foam without holes give only a shallow, faux effect.

What button tufting is

Button tufting pulls the padding into a pattern, usually a diamond or square grid, with a button at each point. There are three common types:

  • Deep diamond tufting gives the strongest pattern. The buttons pull the foam into deep pleats between them.
  • Biscuit (square-grid) tufting uses a grid of squares rather than diamonds.
  • Shallow or faux tufting uses buttons only, with no pleats. The effect is much lighter.

Choose the type before you start, because it decides the foam, the fabric and how much you need.

Plan the button grid

Classic diamonds are taller than they are wide. Button spacing is often about 4 to 7 in (10 to 18 cm), depending on the size of the piece. Mark the grid on the backing board before you cut the foam.

A pegboard with a 1 in grid of holes is a handy template for a headboard. It lets you place the buttons evenly without measuring every point.

Cut holes in the foam

For deep tufting, use foam about 2 to 4 in (5 to 10 cm) thick. Cut a hole at each button point, about 1 in (25 mm) across. Use a sharpened metal tube, a hole saw or an electric knife. Cut through the foam cleanly, so the holes do not tear.

Without holes, the buttons only dent the surface, which is faux tufting.

Allow extra fabric for depth

Deep tufts need more fabric than a plain cover. Measure over the foam and down into the holes. The fact sheet suggests roughly 1.5 to 2 in (4 to 5 cm) of extra fabric per diamond, each way, for deep tufts. Test this on a mock-up first, because the right amount depends on the foam and the fabric. Expect to use much more fabric than a plain cover of the same piece, and the upholstery yardage chart gives plain-cover figures.

Choose and cover the buttons

Common button sizes are #24 (5/8 in), #30 (3/4 in) and #36 (7/8 in). A button kit or a press lets you cover buttons with the same fabric as the chair. Cover them before you start, so you can use the finished buttons as you go.

Set the buttons

You need a long, double-pointed tufting needle, about 8 to 12 in (20 to 30 cm), and waxed nylon tufting twine.

  1. Start at the centre button and work outward row by row. This keeps the pattern even.
  2. Pull the twine through the foam hole and through the fabric, from the front to the back.
  3. Secure the twine at the back. Use a toggle, a washer, a staple or a slipknot, so the button holds.
  4. Pull the button down into the foam hole until the tuft forms, and check the position before you secure it.

Work carefully at the edges. Keep each row straight, because a single misplaced button shows.

Set the pleats

Between the buttons, the fabric forms pleats. Use a regulator to shape and set each pleat. On a backrest, make sure the pleats fall downward, because pleats that face upward collect dust and crumbs. On a seat, check that the pleats face the same way across the piece.

Fabric choice

Plain or small-print fabrics work best. Velvet is the classic choice for tufting, because it holds the pleats well. Thick, stiff or bold-printed fabrics fight the pleats, and the pattern can look distorted. Test a small area before you commit to the full piece.

Common mistakes

  • Pressing buttons into flat foam. Without holes, it gives a shallow, faux effect.
  • Using the same fabric as a plain cover. Deep tufting needs much more.
  • Pleats facing upward on a back. They collect dust.
  • Choosing a bold or thick fabric. It fights the pleats.
  • Starting from the edge. Start at the centre so the grid stays even.

Safety

Long tufting needles are sharp at both ends. Control the exit point of the needle, and keep your other hand clear of it while you pull the twine through.

Button tufting is often used on a wingback or a tight back. For those, see how to upholster a wingback chair and how to upholster a tight back on a chair. For a piped edge to finish the piece, see how to make and attach piping for upholstery.

The complete guide to techniques

Types of Upholstery Techniques Explained
Read the guide

Keep exploring

Guides from other topics

All topics →