Techniques

How to make corners pointy sewing?

How to make corners pointy when sewing: pivot with the needle down, clip about 1/8 inch from the stitching, trim the bulk, and turn the corner out.

On this page
  1. Seam allowance and stitch length
  2. Pivot at the corner
  3. Clip, trim and grade
  4. Turn and shape the point
  5. Press
  6. Knife-edge cushions and dog ears
  7. Common mistakes
  8. Safety
  9. Related steps

To make a corner pointy when sewing, stop with the needle down exactly at the corner, lift the presser foot and pivot the fabric. Clip the seam allowance about 1/8 in (3 mm) from the stitching, trim the bulk, then turn the corner out and push the point out with a point turner.

Seam allowance and stitch length

Upholstery and cushion seams usually use a 1/2 in (13 mm) seam allowance. Garment sewing usually uses 5/8 in (15 mm), so check your pattern before you cut. Shorten the stitch length to about 1.5 mm for the last inch before the corner and the first inch after it. The shorter stitches hold the corner firm when you turn it.

Pivot at the corner

  1. Sew up to the corner point.
  2. Stop with the needle down, exactly at the pivot point.
  3. Lift the presser foot.
  4. Turn the fabric 90 degrees, keeping the needle in the fabric.
  5. Lower the presser foot and continue stitching down the next edge.

On thick fabric, take one or two small stitches diagonally across the corner instead of a sharp pivot. This gives a sharper point than a single pivot on bulky layers.

Clip, trim and grade

Clip the corner diagonally, stopping about 1/8 in (3 mm) short of the stitching. Do not clip right up to the stitches, because the corner can fray or split. The 1/8 in gap leaves enough seam allowance to hold the thread.

On bulky fabric, also taper the seam allowance back from the corner on both sides. If the corner is layered, grade the layers so each one is trimmed to a different width. Grading reduces bulk, so the point turns cleanly.

Interfacing trimmed out of the seam allowance reduces bulk further.

Turn and shape the point

Press the seam open or flat before you turn the piece. Then turn it right side out. Use a point turner, which is a bamboo or plastic tool with a blunt tip, to push the corner out. You can also tease the tip out from the right side with a pin or a needle.

Do not poke the corner out with scissors. The blades can tear through the seam.

Press

Press the finished corner with an iron. On delicate fabrics, use a press cloth to protect the surface from shine and scorch marks. Press from the wrong side where you can.

Knife-edge cushions and dog ears

On a knife-edge cushion, a square-cut piece gives a square cushion corner, but the corner forms a dog ear, a small point that sticks out. To avoid it, taper the cutting line about 1/2 in (13 mm) in at each corner before you cut. This removes the material that would otherwise form the dog ear.

Common mistakes

  • Poking corners out with scissors. It tears through the seam.
  • Clipping right up to the stitching. The corner frays or splits.
  • Cutting square pieces for knife-edge cushions. They form dog ears.
  • Adding extra backstitching at the corner. It adds bulk.

Safety

Keep your fingers clear of the needle when you pivot. Lift the presser foot with the needle down, and check your hand position before you turn the fabric.

For how the same idea applies to a corner on a seat or arm, see how to do upholstery corners. For inside corners on a post, see upholstery inside corners. For a boxed cushion, see how to make a boxed cushion cover for furniture.

The complete guide to techniques

Types of Upholstery Techniques Explained
Read the guide

Keep exploring

Guides from other topics

All topics →