Techniques

Leather Upholstery Corners: Folding and Pleating Techniques

How to fold and pleat leather upholstery corners: skive the fold, trim with care, and fasten with fine staples. Staple holes in hide are permanent.

On this page
  1. Why leather corners need a different approach
  2. Know the hide before you cut
  3. Skive and trim the fold
  4. Folding and pleating
  5. Fastening: fine staples and stitching
  6. Machine sewing leather corners
  7. Can a leather chair be reupholstered?
  8. How to get creases out of leather upholstery
  9. Common mistakes
  10. Safety
  11. Related steps

Leather corners are folded and pleated in much the same way as fabric, but the material is less forgiving. Leather does not fray, so cut edges need no finishing, but every staple and needle hole stays. Skive the bulk out of the fold, trim with care, and fasten the fold on the underside with fine, flush staples.

Why leather corners need a different approach

Fabric can be pulled, eased and re-stapled as many times as needed. Leather cannot. Each staple hole remains, and the hide stretches unevenly, so a corner that looks right on the first try is often the one you keep. Plan the cut, the pleat and the staple placement before you pull the hide taut.

Know the hide before you cut

Upholstery leather is typically about 0.9 to 1.3 mm thick. Thicker is not crisper: thicker leather usually gives bulkier corners, so you need to trim and skive more.

Hides stretch unevenly. The belly stretches most and the backbone least. Where possible, cut corner pieces from the firmer areas, so the corner holds its shape.

Skive and trim the fold

Skive the leather inside the fold with a skiving knife to thin it. Work on a firm surface and cut away from your body with a sharp blade.

Trim the excess from inside the pleat, leaving about 1/4 to 1/2 in (6 to 13 mm). Leather does not fray, so the trimmed edge can stay raw inside the fold.

Folding and pleating

Single pleat. Fold one side over the other so the fold line runs straight down the corner edge. This is the usual choice for thinner pads.

Double pleat. Fold both sides in so two folds meet at the corner. Use this on thicker padding or squarer corners.

Several small pleats work on rounded corners, in the same way as fabric.

Sail fold for thick hides. Pinch the excess into a sail shape and fasten it on the underside of the frame. It leaves less overlap and less bulk, which suits thick leather.

Before you fasten the fold, warm the leather slightly with a hair dryer on low, so it bends without cracking. Test on a hidden area first. Then flatten the fold with a rubber mallet or a bone folder. Do not use a steel hammer face, which can mark the surface.

A dab of contact cement inside the fold can hold a crisp pleat in place. Use it sparingly, and use solvent-based contact cement only with good ventilation.

Fastening: fine staples and stitching

Use fine staples, set flush. Stainless or coated staples resist staining better than plain steel. Stainless staples also reduce the chance of rust marks on light-coloured hides.

Staple holes are permanent, so avoid temporary tacks in visible areas. Place each staple with the hide’s grain and the fold in mind, because a misplaced staple cannot be cleanly removed.

Machine sewing leather corners

Leather can be machine-sewn when a fold will not lie flat or when you are making a cushion or a boxed corner. Use a wedge-point (leather) needle, set the stitch length to about 3.5 to 4 mm, and use a walking foot to feed the layers evenly.

Can a leather chair be reupholstered?

Yes. Leather chairs can be reupholstered, but the work is slower and less forgiving than fabric. The hide needs careful cutting because of its uneven stretch, and every staple leaves a hole. If the chair has a leather seat and back, treat the job as a full project and plan for the extra time. If the hide is badly worn or the frame is weak, a professional may be the better option.

How to get creases out of leather upholstery

Most creases in leather upholstery are wear marks in the grain. Many cannot be ironed out. Light surface creases can sometimes be softened with a leather conditioner suited to your type of leather. Test any product on a hidden area first, because some finishes react badly to conditioners. Do not apply moisture to finished leather, and do not use a hot iron.

Common mistakes

  • Treating leather like fabric. It does not stretch evenly, and it does not fray.
  • Expecting staple holes to disappear. They remain, so place each staple with care.
  • Wetting finished leather to help it fold. It can stain or spot chrome-tanned hides.
  • Assuming thicker leather gives crisper corners. It usually gives bulkier ones.

Safety

Skive away from your body on a firm surface with a sharp blade. When you use solvent-based contact cement, work in a well-ventilated room and keep it away from flames.

For the basic fold and staple order that applies to both fabric and leather, see how to do upholstery corners. If the fabric folds around a post or junction rather than a simple corner, see upholstery inside corners.

The complete guide to techniques

Types of Upholstery Techniques Explained
Read the guide

Keep exploring

Guides from other topics

All topics →