Techniques

How to Upholster a Wingback Chair

How to upholster a wingback chair: strip in reverse order, repair the frame, rebuild the inside pieces first, then finish the wings, arms and outside back.

On this page
  1. Plan the job
  2. Strip the chair in reverse order
  3. Check and repair the frame
  4. Rebuild in order
  5. The seat and deck
  6. Inside pieces and stuff-in
  7. Wings: easing curves and piping
  8. Tack strips
  9. Back the outside panels
  10. Common mistakes
  11. Safety
  12. Related steps

To upholster a wingback chair, strip the old fabric in reverse order, repair the frame, and then rebuild the inside pieces before the outside ones. A wingback is a full project, so plan for a beginner to spend roughly 30 to 60 hours on it. Most of the time goes into the order of work and the curved wings.

Plan the job

Plan the time before you start. A beginner can expect roughly 30 to 60 hours, and a professional will be faster.

Yardage varies a lot between wingbacks, depending on size and on whether the chair has a loose cushion. Measure the actual pieces, and work out a cover plan from them. Then order 10 to 15 percent more than your figure, plus enough for the pattern repeat, so you have room for mistakes.

Strip the chair in reverse order

Remove the pieces in the reverse of the order you will rebuild them. Start with the dust cover, then the outside back, the outside arms, the outside wings, and finally the inside pieces.

Photograph and label each piece as you remove it, as in taking a chair apart for reupholstering. Keep the old pieces flat, because they make cutting patterns for the new fabric.

Check and repair the frame

Check the frame before you add anything new. Reglue loose joints with hide glue or PVA. Replace or add corner blocks where the frame has moved.

Do not skip this step. Loose joints get worse under the tension of new fabric, and a repair made after the upholstery is on is much harder to do.

Rebuild in order

Rebuild the chair in this order:

  1. Seat and deck
  2. Inside arms
  3. Inside wings
  4. Inside back
  5. Outside wings
  6. Outside arms
  7. Outside back
  8. Trim
  9. Dust cover

Inside pieces always go on first. The outside pieces cover the edges of the inside work, so if you start on the outside, you will have to undo it.

The seat and deck

The seat often uses eight-way hand-tied coil springs, or sinuous springs. The deck is the base of the seat under the cushion. Use the show fabric at the front, where it is visible, and a cheaper deck lining, such as denim or muslin, behind it, under the cushion.

Some wingbacks have a loose T-cushion, and some have a tight seat. Check which your chair has before you order the cushion foam.

Inside pieces and stuff-in

Where the inside back, the arms and the seat meet, allow about 3 to 6 in (8 to 15 cm) of stuff-in. This is extra fabric pushed into the gap, so it does not pull out when someone sits down.

Ease the fullness at any curve with small pleats or gathers. Do not try to force a curve flat.

Wings: easing curves and piping

The wing is curved, so it is not one flat piece. Ease the fabric around the curve with small pleats or gathers, or cut the wing in sections so the curve has seams. Pull the fabric smoothly, and check the shape before you staple.

The front edges of the wings are usually piped. See how to make and attach piping for upholstery for the method.

Tack strips

Use a cardboard tack strip to back-tack the top edges of the outside panels. Use a metal tack strip, often ply-grip, to close the straight sides. For curved wing edges, a flexible curve-ease strip fits the curve better.

Metal tack strip teeth are sharp, so wear gloves when you handle it.

Back the outside panels

Put a layer of batting or a cardboard stiffener behind each outside panel. Without it, the outside back can sag over time.

Common mistakes

  • Working on the outside pieces first. The inside pieces go on first.
  • Skipping the frame repair. Loose joints worsen under the new tension.
  • Ordering exact yardage. Add 10 to 15 percent, plus the pattern repeat.
  • Covering the wings in one flat piece. The curves need easing or seams.

Safety

Wear gloves when you handle metal tack strip, because the teeth are sharp. Wear eye protection when you remove tacks and staples.

For a tufted back, see how to do button tufting on upholstered furniture. For the back on a chair without wings, see how to upholster a tight back on a chair. For a first full project, see can you teach yourself upholstery.

The complete guide to techniques

Types of Upholstery Techniques Explained
Read the guide

Keep exploring

Guides from other topics

All topics →