Reupholstering an antique couch means taking it apart in a controlled way, repairing the frame and springs, rebuilding the padding, and fitting new fabric and trim. Decide what to keep first, because original parts may be worth keeping for their value or as evidence. Then document the piece, strip it in reverse order, repair, rebuild, and re-cover. It is slow work. Professionals often spend 20 to 40 hours or more on a traditional sofa.
Get it appraised and decide what to keep
If the couch may be valuable, get it appraised before you start. Original upholstery and a maker’s label can both affect value.
You can also consider conservation work, which keeps original parts where possible. It is less intrusive than a full re-cover, and it can help preserve value.
Photograph and label before you strip
- Photograph each side and each layer before and during stripping.
- Label old pieces so you can reuse them as patterns.
- Keep fabric samples, maker’s labels, and old layers as reference.
Tools
- A ripping chisel and mallet
- A tack lifter and a staple remover
- Pliers
- A webbing stretcher
- Curved needles
- A regulator, for working the hair or fiber into shape
- A magnetic tack hammer or stapler
Strip the old upholstery
Strip the couch in reverse order:
- Dust cover
- Outside back
- Outside arms
- Inside back
- Inside arms
- Seat
Pull old tacks and staples carefully, and save intact pieces as patterns.
Repair the frame and springs
- Joints. Reglue loose joints with hide glue. Hide glue can be undone later, which suits antique repairs.
- Webbing. Jute webbing is usually 3.5 to 4 inches wide. Stretch it with a webbing stretcher, interweave it, and fix it with 1/2 to 5/8 in tacks or staples. Fold the ends over.
- Springs. Replace broken coils. Re-tie eight-way springs with jute or polyester spring twine, and sew each spring to the webbing in three or four places. Old springs are not automatically junk, and many just need re-tying.
Rebuild the padding
- Sound horsehair can be teased and reused.
- Add new burlap and muslin, then cotton or polyester batting.
- Foam does not suit every antique. Hair and stitched edges keep the original shape, and foam can change it.
The horsehair stuffing guide explains how to check and reuse the hair.
Cut and attach the new fabric
Re-cover the couch in this order:
- Seat or deck
- Inside arms
- Inside back
- Outside arms
- Outside back
- Trim
- Dust cover
For fabric, a typical three-seat sofa takes about 14 to 20 yards of 54-inch fabric. Large pattern repeats need more. Measure from the existing cover pieces rather than from the overall size of the couch, and buy extra for pattern matching and mistakes.
Trim and finish
Attach gimp or double welt with gimp pins or hot glue. Finish the underside with a dust cover.
Time, cost, and when to hire
- Professionals often spend 20 to 40 hours or more on a full traditional sofa, depending on its condition.
- Costs vary a lot by region and by how much structural work is needed. Get written quotes.
- Professional reupholstery can cost more than a new mid-range sofa. Factor that in before you commit to a valuable piece.
Safety
- Wear an N95-type mask. Old stuffing holds dust, mold, and pests.
- Test old finishes for lead before you sand.
- Wear eye protection. Tacks and staples fly when they are pulled.
- Some older green fabrics used arsenic-based dyes. Wear gloves and a mask when you handle them.
Common mistakes
- Assuming reupholstering is always cheaper than buying new.
- Throwing out springs that only need re-tying.
- Putting foam into an antique that was built with hair and stitched edges.
- Measuring fabric from the whole couch rather than from the existing cover pieces.
For identifying a Victorian-era piece before you start, see reupholstering Victorian furniture. If the cushions are the only part that needs work, how to replace foam in sofa cushions covers that job.