Yes. You can upholster a bed frame yourself by padding the headboard, footboard, and side rails with foam and batting, then covering them with fabric and stapling it off. You can build a new wood base first, or cover an existing frame. Either way, most of the work is measuring, padding, and stretching the fabric evenly.
Measure for your mattress
Measure the mattress before you cut anything. Typical US sizes are:
| Size | Dimensions (in) |
|---|---|
| Twin | 38 x 75 |
| Full | 54 x 75 |
| Queen | 60 x 80 |
| King | 76 x 80 |
| California King | 72 x 84 |
The headboard width is usually the mattress width plus about 2 to 4 inches, or the width of the frame, depending on the design. Measure the mattress you will actually use, because thickness and dimensions vary between brands.
Materials and tools
- Panels. 1/2 to 3/4 in plywood or MDF for the headboard and footboard.
- Rails. 2x4 or 1x8 boards for the frame and supports.
- Foam. 1 to 4 in for the headboard (2 in is common). Use 1/2 to 1 in foam, or batting only, on the side rails and footboard.
- Batting. Polyester batting over the foam.
- Adhesive. Foam-safe spray adhesive.
- Fabric. Upholstery-weight fabric. The standard width is 54 in. Plan for the pattern repeat, and check whether running the fabric sideways (railroading) saves yardage.
- Staples. 3/8 to 1/2 in legs. A pneumatic or electric stapler handles hardwood and MDF better than a manual one.
- Saw and drill, if you build the base.
Prepare the frame
- Remove the legs, hardware, and slats before you cover anything.
- Mark the bolt holes so you can find them later.
- If the existing rails are sound, you can wrap them rather than build a new frame.
Pad the panels
Bond the foam to the wood with foam-safe spray adhesive. Add a layer of polyester batting over the foam so the fabric lies smoothly. Work in a ventilated space when you use spray adhesive.
Watch the thickness on the rails. Thick foam on the rails can stop the mattress from fitting, so keep side-rail padding thin.
Cut and fit the fabric
Cut each panel’s fabric to the panel size, plus the foam thickness, plus about 3 to 4 inches on each edge so it wraps to the back. Plan the pattern repeat before you cut.
Use upholstery-weight cloth. Thin fabric shows staples, foam seams, and stains.
Stretch and staple
- Lay the fabric face down, place the padded panel on it, and center the panel.
- Staple the center of one side, then the center of the opposite side.
- Work outward toward the corners, alternating opposite sides and pulling the fabric taut without distorting the panel.
- At the corners, fold neat pleats or miter the fabric. Trim the bulk before the final staples.
Optional: button tufting
Mark a grid or diamond button tufting layout on the headboard. Drill through the panel at each point, then pull the buttons through with a long needle and upholstery twine. Staple the twine off at the back.
Finish and assemble
- Cover the back with cambric or lining for a clean finish. This is optional.
- Reattach the legs and hardware. Join the headboard, side rails, and footboard with bed brackets or bolts.
- Reinstall the slats, then the mattress.
Common mistakes
- Using thin fabric that shows staples and seams.
- Adding so much foam to the rails that the mattress will not fit.
- Assuming flat panels need sewing. Stapling is usually enough.
- Covering the frame before you mark the bolt holes.
- Using spray adhesive without ventilation.
If you would rather build a sofa frame, see how to build a DIY sofa wood frame. For the parts of an upholstered piece, see how upholstered furniture is built.