Short answer
To reupholster a chair seat with vinyl, remove the seat, strip the old cover, and replace or trim the foam. Cut the new vinyl with 2 to 3 inches of extra material on every side. Then stretch and staple it, starting from the center of each side and working outward. Fold or trim the corners, add a dust cover, and reattach the seat.
What you need
- Upholstery vinyl. Choose upholstery-grade vinyl with a double-rub rating of about 15,000 or more, or marine vinyl. Avoid tablecloth vinyl, which isn’t rated for upholstery.
- Foam. Use 1 to 2 inches of high-density foam. Polyester batting is common for a softer top layer.
- Tools. A staple remover, an upholstery stapler, sharp scissors or a utility knife, a heat gun or hair dryer, and a screwdriver.
- Staples. Use staples with 1/4- to 3/8-inch legs for most hardwood frames. Pneumatic staplers take 22-gauge, fine-wire (71-series) staples.
- Dust cover. Black cambric for the underside.
- Spray adhesive (optional). It can help hold new foam to the base.
How much vinyl to buy
Upholstery vinyl is commonly 54 inches wide. One yard usually covers two to four dining chair seats, depending on seat size. Add 2 to 3 inches of allowance on every side for gripping and wrapping. Typical upholstery vinyl weighs about 26 to 35 ounces per linear yard.
Prices vary a lot by grade and retailer, so compare the rub rating, not just the price.
Step 1: Remove the seat and strip the old cover
Unscrew the seat from underneath the chair and set the hardware aside. Pull out the old staples and peel off the worn vinyl. If you can, keep the old cover intact, since it works as a cutting pattern.
Step 2: Check and replace the foam
Flattened or crumbled foam won’t support new vinyl well, so replace it. Trace the backer board onto new high-density foam, cut it to size, and glue it to the base if it needs holding.
Step 3: Lay out the vinyl
Place the cushion face-down on the vinyl. Mark and cut the vinyl using the old cover as a pattern, with 2 to 3 inches of extra material on every side.
Vinyl usually stretches more across its width than along its length. Position the piece so the greater stretch runs from side to side over the seat. If you’re unsure, test the stretch on a scrap first.
Step 4: Stretch and staple from the center out
- Staple one staple at the center of each side: front, back, left, and right.
- Work outward toward the corners, alternating sides as you go.
- Pull firmly and evenly. Overstretched vinyl thins and can tear at the staples over time.
Use clips to hold the vinyl in place, not pins. Pin holes are permanent.
Step 5: Finish the corners
A heat gun helps the vinyl ease around curves and corners. Set it to low, hold it 6 inches or more away, and keep it moving.
Fold neat pleats at the corners, or trim the bulk first. Cut no closer than 1/2 inch to the staple line.
Step 6: Add a dust cover and reattach the seat
Staple black cambric to the underside to protect the staples and keep dust out. Trim any extra vinyl, then reattach the seat to the frame.
Sewing vinyl
If you need to sew vinyl, such as for a seam or piping:
- use a size 16 to 18 needle
- use bonded nylon or polyester thread (Tex 70, or #69)
- set a stitch length of 3 to 4 mm
- use a walking foot or a Teflon foot to help the vinyl feed
- hold layers with clips, not pins
A leather wedge needle can perforate vinyl. A sharp or standard needle often works better.
Common mistakes
- Stretching too tight. Overstretched vinyl splits at the staples over time.
- Using the wrong vinyl. Tablecloth vinyl isn’t built for upholstery.
- Working with cold vinyl. Cold vinyl is stiff and may crack. Work at room temperature.
- Using a leather wedge needle on vinyl. A sharp or standard needle often works better.
Safety
- Wear eye protection when you pull and drive staples.
- Overheated PVC scorches and gives off toxic fumes. Keep the heat gun moving, and don’t hold it in one spot.
Recover, repair, or replace?
- Recover when the foam is sound and the old cover is worn but intact.
- Repair small cracks, tears, or fading first. See how to restore vinyl furniture.
- Replace the foam if it has flattened or crumbled. Replace the cover when cracks are widespread, the backing shows, or the foam has crumbled.
After the job, keep the vinyl out of direct sun and away from heat. See faux leather furniture care for cleaning, and vinyl and faux leather upholstery durability for what to expect from the material over time.